|
Post by BladeRunner now OLD FLASH!!!!! on Aug 12, 2008 13:09:56 GMT -5
i'm upgrading from the old rg58 coax. I notice htere is an rg8x now that I'm notfamiliar with. Is this comparablr with rg8 and is it as good as rg8? What's the difference between the two ?
|
|
|
Post by Tombstone (R.I.P.) on Aug 12, 2008 14:14:32 GMT -5
I'm sure that their will be more information posted about this but RG8X is a smaller diameter than RG8 but larger than RG58 and is more flexible and to hook up watt meters, indoor general radio jumpers. The quality depends on it having a stranded center conductor and as much shielding as possible. I use the RG8 for outdoor use where it leaves my last switch and runs to the antenna, I would imagine that the RG8 will weather better and maybe have a lower loss.
Tombstone
|
|
|
Post by mark4 on Aug 12, 2008 20:37:33 GMT -5
I use Belden 9913F7. This is the best bang for the buck. Double shielded and some what flexible. And at 27MZH it is very low loss. Check out Palco Electronics in MI. He has the best deal going, last time I ordered.
|
|
2tn1326
Mudduck
DXRadioWorld.com
Posts: 9
|
Post by 2tn1326 on Aug 12, 2008 21:30:23 GMT -5
|
|
**GRUMPY**
Administrator/The Boss
Classic Radio Operator Olde Timer 8220 [/color][/center]
"The King of Ping"
Posts: 4,342
|
Post by **GRUMPY** on Aug 12, 2008 22:10:40 GMT -5
i'm upgrading from the old rg58 coax. I notice htere is an rg8x now that I'm notfamiliar with. Is this comparablr with rg8 and is it as good as rg8? What's the difference between the two ? What type of antenna are you going to be using this coax on? If you're going to be using this for a base install I would not use RG58 or RG8X. I use RG 213 for all of my base antenna installs!
|
|
|
Post by BladeRunner now OLD FLASH!!!!! on Aug 12, 2008 23:34:37 GMT -5
Now you've thrown me a curve. RG213? It's for a base setup. Learn something new every day. I do appreciate the info and that's why I asked.
|
|
**GRUMPY**
Administrator/The Boss
Classic Radio Operator Olde Timer 8220 [/color][/center]
"The King of Ping"
Posts: 4,342
|
Post by **GRUMPY** on Aug 13, 2008 3:48:12 GMT -5
|
|
|
Post by spitfire441 on Aug 13, 2008 5:17:01 GMT -5
I overkill with: Times Microwave LMR-400 on my PDL-2, and way overkill on my 5/8 GP is Andrews 1/2" Heliax.
|
|
|
Post by mark4 on Aug 13, 2008 18:15:27 GMT -5
I'm still happy with 9913F7. I checked out the loss at 100ft compared to just about anything else. At 27MHZ the loss was minuscule. But we all have our favorite brands radios etc. 213 and LMR is great stuff. ;D
|
|
|
Post by swamp40 on Aug 14, 2008 14:13:58 GMT -5
Might take a look at "BURYFLEX" or the "COMSCOPE" line of coax . I have put 1500 watts on RG-8x (140 feet on 10 meters) with no adverse effects and use it or comscope for HF through 440 .
|
|
|
Post by marconi390 on Aug 15, 2008 0:54:15 GMT -5
Bladerunner, I just tested 135' of Bury Flex RG-213 with a dummy load and meter. I input 75 watts of FM carrier and got 73 watts out. I have 150' of RG8x and I did the same, 75 watts in and 55 watts out. The small coax is very good, but it does show more loss due to line length than the bigger coax. IMO, 9913 is very good and low loss as well, but you might have moisture problems with it outside, it is like a sponge with all the air insulator inside.
|
|
|
Post by Afterburner(OT-749) on Aug 15, 2008 13:54:29 GMT -5
Because this has been a topic on coax, I have a question for those who know more than I (which by the way is nothing) about some rolls of coax that I have here at home. The one roll is one of those LARGE (1000 ft.) rolls of what is marked TFC-TX10 15 Series, and the other which is a 500 ft roll is marked TFC-T10. What is this coax used for? My other question would be how do you "test" the impedance of coax? I have some very nice Fluke meters but no knowledge how to test coax to see if it is say 50 ohm, 75 ohm etc...
|
|
|
Post by BionicChicken on Aug 15, 2008 21:09:14 GMT -5
|
|